14

Project R35 GT-R, Really Improving the Aero with Verus Engineering

By Mike Kojima

While its somewhat bulky looks are deceiving, the DBA R35 GT-R is one of the most aerodynamic cars currently in production with a Coefficient of drag of.26.  This puts in in the top 10 of production sedans with low drag coefficients. 

When the GT-R was facelifted in the 2012 model year from the CBA to the DBA configuration the aerodynamics were tweaked to bring a decrease in the drag coefficient from .27 to .26 while having a slight increase in the amount of downforce generated.  This is amazing as nearly all production cars have some about of lift at speed.  Since the aerodynamics of the stock GT-R are so good, we were really reluctant to mess them up with some misguided aero kit parts. 

Here is where Verus Engineering comes in.  They have come up with a few unobtrusive and almost invisible parts that not only lowers the GT-R's drag coefficient to a mind-bending .25 but also increase downforce by 13% at 100 mph.

The first group of parts was a set of Verus's diffuser strakes. Stock the GT-R has remarkably good underbody aero and the strakes enhance the effectiveness of the factory rear diffuser.

The car was designed from scratch by Nissan to have good underbody aero and thus almost has a flat bottom from the factory.  This helps the stock rear diffuser actually be pretty effective, however it can still be improved upon.

Since the rear diffuser helps the car develop downforce by changing the bodies overall shape from one very roughly resembling an airplane wing to one that has more of an inverted wing shape, the way the air flows through the diffuser is critical.  The Verus engineering parts optimize this.

There are 4 strakes in total in the Verus kit, two outer ones, and two inner ones.  They have unique shapes that were derived via CFD analysis. 

The shapes create vorticities that strongly attach the flow of the diffuser to the roof and clean up the flow field behind the car. 

The second part of the Verus Engineering system is this carbon fiber belly pan extension. The GT-R basically has a flat bottom except for an area around the middle of the car which is open presumably to allow exhaust heat to escape. 

The Verus part covers this area with this carbon belly pan which has CFD optimized venting to help keep the exhaust system cool enough while greatly reducing drag.

Here are the strakes bolted to the factory diffuser on Project GT-R. The installation is very easy and takes only a few minutes. 

Verus Engineering supplies a drilling template to create the mounting holes for the strakes in the stock diffuser. Although the drilling is simple, care needs to be taken when drilling the holes as the factory carbon diffuser is super expansive, it sells for almost $3000!

 

 

Page 1 of 3 Next Page
Bookmark and Share
Comments
Bradl3y76
Bradl3y76link
Tuesday, May 15, 2018 10:38 PM
I don't have their wares on my car currently, but will when I finish a few other areas in need of attention. Their stuff is fantastic.
Mike Kojima
Mike Kojimalink
Tuesday, May 15, 2018 11:48 PM
Yes they have CFD designed aero for many cars, not just the GT-R
ThisGuy
ThisGuylink
Wednesday, May 16, 2018 8:45 AM
Would you say the NACA ducts in the diffuser are to aid the top side of the diffuser or for cooling various items above the diffuser?
MattAtPlaton
MattAtPlatonlink
Wednesday, May 16, 2018 10:23 AM
Great products! Just careful with those speed bumps...
Mike Kojima
Mike Kojimalink
Wednesday, May 16, 2018 1:34 PM
@ThisGuy, they are to cool the CV joints, transaxles, exhaust, driveshaft joints
Rory
Rorylink
Friday, May 18, 2018 10:19 AM
When you guys plan to do some power on this car, bring the car over to us at SP Engineering :)
engineered
engineeredlink
Sunday, May 20, 2018 5:33 PM
Are you really sure you can feel the difference between .26 and .25 CoD?
Post Comment Login or register to post a comment.

MotoIQ Proudly Presents Our Partners:



© 2018 MotoIQ.com