Ford

 

29

TESTED: Ford Mustang GT Power Packs 1-3

by Billy Johnson

Ford Performance offers three different 50-state legal “Power Packs” for the 2015-2017 Mustang GT that increases horsepower without affecting the factory warranty*.  We back-to-back test Power Packs 1, 2, & 3 on a stock Mustang GT to see if Ford’s claim of 13-37hp increases are legitimate.  We then analyze the GT350 intake manifold’s effect on the torque curve to see if it really has less low-RPM torque than stock in favor of high-RPM power.  Finally, we determine which packages would be best for street and track use through in-depth torque and gear ratio analysis.


 

[Read the rest of this article...]

10

TESTED: Ford Performance Cat-Back Exhaust and GT350 Valence

by Billy Johnson

The Ford Mustang may be the best-selling sports car in the world at the time of this writing, yes you read that right, but it is far from the best sounding sports car in the world. We reached out to Ford Performance for their far more attractive and aggressive M-5200-M8TBV Touring Exhaust System and GT350 lower valence with integrated quad-tips to improve the looks and sound of our S550 Mustang GT.


 

[Read the rest of this article...]

01

Tested! Honeywell Garrett Upgraded Intercooler for the EcoBoost Mustang

by Mike Kojima

Honeywell by Garrett has recently released a direct fit bolt-on intercooler solution for the EcoBoost Mustang, and we didn't wait any time to verify how it performs! We knew our friends at HPS Performance Products had been time attacking their EcoBoost Mustang, so it would be the perfect test bed for our intercooler test. Read on for all the details and DATA!


 

[Read the rest of this article...]

19

Project Mustang 5.0: Data Logging, Tuning, and More with HP Tuners nGauge

by Vince Illi

HP Tuners has been at the forefront of automotive engine tuning and diagnostics for Ford, General Motors, and Chrysler vehicles for over a decade now. Their VCM suite is used for tuning by professional speed shops around the world. Furthermore, HP Tuners is one of the only aftermarket companies who has completely “unlocked” the Copperhead Powertrain Control Module (PCM) used in Ford’s latest engines, including the Coyote 5.0 V8. Their VCM Scanner is available to consumers and can perform the vast bulk of factory-level diagnostic testing on a laptop computer—tools normally only available to Dealers using Ford’s expensive Intelligent Diagnostic Scanner (IDS) tool.

Recently, HP Tuners partnered with E-Motion products to create a new handheld tuner device with a twist. The aftermarket is already flooded with OBD-II tuning devices that run the gamut from good to terrible, so HP Tuners wanted to set themselves apart by making something that could do more than just standard tuning.


 

[Read the rest of this article...]

17

Whiteline S550 Ford Mustang - Introduction and Initial Testing

by Mike Kojima

Recently, Whiteline obtained a late model S550 Mustang to function as both a test mule for their S550 chassis parts development program, but to also act as a rolling showcase for their Mustang product line. The Mustang will also feature upgrades to the engine, braking system, and the car's cosmetics to make it an all around performer. We will be documenting the build and testing progress here on MotoIQ. 


 

[Read the rest of this article...]

28

AutoX’ing Steed: Gregg Biddlingmeier’s 1988 Ford Mustang

by Justin Banner

It’s not the first choice of those who go autocrossing or tracking, but when a Fox-body Mustang is set up right, it can make for a potent road racer. Gregg Biddlingmeier’s example is one of many he’s owned and shows what these Fords are capable of with some planning, fabrication, and execution.


 

[Read the rest of this article...]

22

Tested: Radium Engineering Coolant Expansion Tank

by Vince Illi

Recently, Radium Engineering released a kit to easily install their Coolant Expansion tanks onto 2011+ Mustangs. We test it out on our Grey Project Mustang 5.0 and discuss how an expansion tank works!


 

[Read the rest of this article...]

26

Project S550 Mustang GT: Installing Airlift Suspension Digital V2 

by Nathan Brummer

In planning the next phase of Project S550 Mustang GT, we began looking at suspension kits that would give the versatility of a comfortable daily diving experience and still provide a somewhat capable track setup. Before we move forward, it’s also important to revisit our goals with this project. This is NOT an all out performance track car, but rather a daily driver that we want to transform into a competitive street car. It’s something that will see light track day action, as well as something that we can show off at local car shows. Given this direction, this build will come to points where compromises are made for street-ability and comfort. While a race-spec coilover kit would be a great solution for the track, daily driving this kit would be less than desirable. Having made this mistake on previous daily drivers, we were determined not to do the same with this project!


 

[Read the rest of this article...]

20

Project E46 M3: Part 18 – Project M3 vs E90 M3 V8

by Pablo Mazlumian

We were pleased with our S54 3.2-liter in stock form, and the goal was to bring it up to V8 M3 performance. Was a 12% power improvement and 90-lb fat reduction enough? Find out inside! We test them to speed and in the quarter-mile. We also compare them from 30-100 MPH in third gear to compare low- and mid-range torque for you track guys! And why not--we even throw in a Mustang GT 5.0 in there...


 

[Read the rest of this article...]

07

Project S550 Part 3: Looking Better with Wide Project6gr Seven Wheels, Cervinis Ram Air Hood, AirDesign Front Fascia & More!

by Nathan Brummer

In our last update, we focused on improving the stock handling of Project S550. While we still have some suspension work to do (and we have some big plans in mind), we’re going to pause on that while we turn our attention to the car’s appearance. The 2015 Mustang has become extremely popular and they look great right out of the box but, given that popularity, we need to do something to make this project stand out from every other Mustang on the street. We’re not looking to do anything extreme or over the top, so we’ll concentrate on making subtle changes that accentuate Ford’s already stellar design.


 

[Read the rest of this article...]

01

Industry Insider: A Tour Through Aeromotive Fuel Systems

by Pablo Mazlumian

We bring you a MotoIQ-exclusive tour one of the fuel system industry's greats.  We get to learn some of Aeromotive's secrets to success, and even get to poke around some of its professional racecars!


 

[Read the rest of this article...]

30

Making the Ford F-150 Ecoboost Drive and Tow Smoother with Eibach Shocks

by Rathyna Gomer

My dad's Ford F-150 Ecoboost is something I frequently drive, usually to pick up car parts and to tow one of the racecars out to the track. Similar to many folks who also own a racecar, the majority of my focus and money has gone into the racecar, not the tow rig. In actuality, I'm spending hundreds of more hours in the truck picking up parts for the car and towing the car to the track, than actually driving on the track. 


 

[Read the rest of this article...]

22

Project 5.0 Mustang (The White One) Building the 302 Coyote Engine!

by Mike Kojima

We were eager to get into our motor and install the Ford Motorsports parts that would basically enable us to rev to over 8000 rpm reliably and breathe better on top. The parts we accumulated would bring us to a spec about the same as the Ford Motorsports Aluminator performance crate engine and a little bit more than the Drag Racing Cobra Jet NA engine. 


 

[Read the rest of this article...]

25

M2K Motorsports 280 mph Ford GT

by Mike Kojima

The Ford GT was in our opinion America's first true exotic supercar. Inspired by Ford's GT40 race cars from the 60's, the Ford GT's performance as a street car easily eclipsed the race cars of yore.  Produced from 2005 to 2006, only 4038 of the cars were ever built making the Ford GT a desirable collectors car that fetches several hundred thousand dollars on the used car market, up from the original asking price of $139,000.


 

[Read the rest of this article...]

14

Project S550: Part 2 - Addressing Shortcomings in the Suspension and Drivetrain

by Nathan Brummer 

We’ve gotten pretty familiar with Project S550 since our last update, having logged several thousand miles to date. While we’re still very much in love with the car, it has begun to reveal some of its quirks and shortfalls but, like any good relationship, we’re willing to work through these in exchange for our long-term goals. As with any good therapy session, it’s time to be completely honest and get all those ugly irritations and disappointments out in the open. We’ll start by recapping the issues we’ve encountered and then outline what we’ve done to address them.


 

[Read the rest of this article...]

20

Project 5.0 Mustang (The White One) Building the Bottom End

by Mike Kojima

In the last segment covering the engine build on our 5.0 liter Mustang, we addressed the top end with CNC ported heads and camshafts from Ford Motorsports. Now it's time to fortify the engine's bottom end so we can have a screaming high-revving naturally aspirated Coyote engine that is still reliable. 

Our target for this build is to have a safe 8000 rpm redline, wheel horsepower in the high 400 range and run on 91 octane California pump gas with reliability and track car endurance. We feel that this stuff is all pretty easily done.


 

[Read the rest of this article...]

24

Project 5.0 Mustang (The White One) Making it Stop with Essex Parts AP Radi-CAL Brake System

by Mike Kojima

Our Project Mustang came stock with pretty decent brakes. From the factory our Ford features 4 piston Brembo calipers with 355x32mm one piece rotors. However, we still wanted to upgrade our brakes as our much wider tires, 20" wheels, upgraded suspension and engine would stress the brakes a lot more. Our Mustang also weighs a punishing 3700lbs with really cooks the brakes. The Ford factory has put larger brakes on some of the higher end SN197 Mustangs so we figured we should follow suit as well.


 

[Read the rest of this article...]

06

An Inside Look at mountune's GRC Ford Duratec Engine!

by Mike Kojima

The current engines used in today's GRC Rallycross racers are some of the highest stressed production based engines in all of Motorsports.  Only Import Drag Racing engines see more stress and perhaps no production based race engines not even Time Attack engines are stressed for as long a period of time as Rallycross powerplants.

Breathing through a 45mm restrictor that limits power to "around" 550 hp, the mountune Ford Duratec puts out 625 lb/ft of torque.  Because of the restrictor, the Garrett Turbo pumps in 45 plus psi absolute of boost to make that power, generating an amazing 3200 psi of cylinder pressure.  To put this in perspective, this is more cylinder pressure than the Audi LMP1 Diesel!


 

[Read the rest of this article...]

19

K&N Mustang American Iron RTR

Fully Filtered: Dave Martis’ K&N Engineering Ford Mustang RTR

by Justin Banner

NASA’s American Iron series is the modern equivalent of the Trans Am Series of the 60's and 70's; where Ford, GM, and Mopar cars slug it out in American Iron (AI) and the cars follow a weight to power ratio much like our own MPTCC series. In addition to AI, NASA also has classes for American Iron Extreme (AIX), where rules are more lax and horsepower gets insane; and Spec Iron (SI), where cars are built to one specification with the 05-10 Ford Mustang being the only chassis allowed. Dave Martis competes in the AI class with his K&N Engineering Ford Mustang RTR and has allowed us to show you the details of his amazing ride!


 

[Read the rest of this article...]

20

Project Focus ST: Getting More Power with Cobb Tuning!

by Mike Kojima

In our last segment of Project Focus ST, we reviewed some parts from Cobb Tuning for our car. To get a nice safe boost in power, we got a Cobb Stage III upgrade which includes a V3 Access port ECU flasher, larger more efficient intercooler, larger charge pipes, a cold air intake, a larger freer flowing downpipe, a freer flowing exhaust and a heavy duty motor mount.  In this installment it's time to put these parts to the test!


 

[Read the rest of this article...]

Page 1 of 4First   Previous   [1]  2  3  4  Next   Last   

MotoIQ Proudly Presents Our Partners:



© 2017 MotoIQ.com