08

Along a private frontage road in the middle of nowhere, Kansas, our 2JZ is getting some miles put on it.  It’s a beautiful day and the top is off—it almost can’t get any better than this (except I’d rather smell the ocean breeze than cow manure).  The 2JZ-GTE engine was built by Four Rings Performance using JE Pistons and K1 rods, and installed at Modified by MKC.  That's a Shine Auto Projects diffuser I'll be talking about next time.

Project Toyota Supra Mark IV: Part 9 – It’s back!

And the 2JZ is running better than ever!

by Pablo Mazlumian

I know, I know!  Part 8 was published over 9 months ago.  Trust me, taking this long for the next installment wasn't part of the plan.  In fact, the car has actually been running since late May.  Unfortunately, a couple of issues reared their ugly heads, and it was hard to sit down for hours on end to bring you an update when all we wanted to do was get this car done.  But things are good now, and we promise to bring you up to speed with all that’s transpired.

 


"Ya not gonna see those things in Nazzcar!"  For the first 500 miles, the car was left with the boost set at the wastegate spring at 18 PSI on pump 93 octane.  The first day I picked up the car from Modified by KC, I was off to Fast Fridays, which is a cool, bi-weekly meet in Overland Park, Kansas.  You can catch our coverage of this meet HERE.

It's been a while since our Supra has graced these pages, so let me bring you up to speed on the car itself.  This is what the engine bay looks like today. 

This 2JZ is powered by a Precision Turbo 6766 turbocharger which pumps air through a 4-in ETS intercooler and a port-matched Hypertune intake manifold with its own 90-mm throttle body.  From there the air channels through the FRP-built cylinder head with Ferrea 1-mm oversized valvetrain and Titan 272 cams.  The exhausted gases escape out a PHR exhaust manifold and 3.5-in MKC-fabricated exhaust system. 

The engine is kept cool with a large PWR all-aluminum radiator, and the stock clutch fan was replaced with dual Flex-a-lite puller fans on the back of the PWR unit.  Other components you may notice here are Boost Logic pulleys, AEM cam gears, Gates engine belts, AEM filter, PHR power steering relocation reservoir, PHR catch can, an Aeromotive fuel pressure regulator and lots of Aeromotive fittings.

 


Instead of the factory plastic engine cover, we installed PHR’s polished cover for a little engine dress up.  Like the factory unit, PHR’s engine cover also has openings to let heat escape from the cylinder head and lengthen the life of the coil wiring underneath there.

Here we see the PT6766 turbo protected by an AEM “dry” filter.  MKC also took our yellowing intake tube and polished it for us to help match the rest of the engine bay.  At some point we’ll have to polish up the turbo compressor housing as well.
Page 1 of 12 Next Page
Bookmark and Share
Comments
ginsu
ginsulink
Tuesday, December 09, 2014 6:22 PM
Congratulations! Thank god we got some cheap gas for a little while so we can enjoy our cars on the road.

I'm a bit of a suspension guy, so I really like the active EDFC upgrade. It sounds like you can do some interesting tuning with that thing. I guess right now, with the F/R control you can build a dynamic 'Launch' and 'Braking' setting that would crank up the rebound and help control squat and dive.

I can imagine in future versions they will build in provisions to control each damper individually so you can tune the car for cornering. I'm hoping one day to get rid of swaybars altogether and use dynamic damping to control body roll (this should save weight and make the suspension much more supple over small bumps). I've heard that they do this in the newer McLarens, although with a much more sophisticated setup, which I think is very similar to the KDSS they use on the Toyota Land Cruiser and 4Runner.
Wrecked
Wreckedlink
Tuesday, December 09, 2014 7:19 PM
Nice work. One thing though, with all those an fittings, you should use the proper fittings on the flex fuel sensor as well, instead of pushing the hose on and clamping.
Dusty Duster
Dusty Dusterlink
Tuesday, December 09, 2014 9:56 PM
This is my favorite MotoIQ project car. Well, other than mine, of course. :-P

I'm glad you finally get a chance to drive it! I want a ride next time I'm in KC.
theneil
theneillink
Wednesday, December 10, 2014 10:18 PM
are there black flecks from those nice new tires on the diffuser? if so good work awesome results pablo
Pablo Mazlumian
Pablo Mazlumianlink
Friday, December 12, 2014 5:22 AM
Thanks for reading guys.
@Ginsu: Yes that would be a sweet setup to control all four corners individually. With handling I'm going to play with adjusting the shocks to slightly stiffen once a certain G-load is hit in cornering, but not much, simply because it is full F/R adjustment indeed.
@Wrecked: Agreed
@Dusty: sounds good!
@theneil: to be honest I've yet to be able to drive the car on the new tires. The day I got them on the weather broke and got too cold (it happens suddenly here). I will say this, however: the night before I was trying to get a feel for a slightly detuned version of the new found power we hit for Part 10 coming soon, and I tried a few third gear "burn outs" to warm the tires up to get of a feel for it in fourth gear, but as soon as I laid into it about 80-90mph the car got all over the place. So it's off to tune the traction control next, but I need new wheel speed sensors first, too. lol.
theneil
theneillink
Friday, December 12, 2014 9:33 PM
hahah mission accomplished
Anonymous User
Anonymous Userlink
Sunday, February 01, 2015 11:07 PM
Post Comment Login or register to post a comment.

MotoIQ Proudly Presents Our Partners:



© 2018 MotoIQ.com