New! 2007-2013 Nissan Altima Sway Bar From STILLEN – Coupe or Sedan

New! 2007-2013 Nissan Altima Sway Bar – Coupe or Sedan

STILLEN is proud to announce the launch of the Nissan Altima rear sway bar. This rear sway bar has gone through extensive R&D and testing to eliminate the common Nissan Altima rear sway bar defect. Due to many complaints from customers and vehicle owners, STILLEN decided to take a very close look into the design of the factory 2007 to 2013 Nissan Altima rear sway bar. In doing so, the engineers discovered that the cause of the failures is the design of the bar and the way the leverage is applied to the bar.

The first thing the STILLEN engineers did was examine the entire suspension of the Altima rear end. To do so, they started by removing the driver side rear spring. This allows them to put a jack underneath the rear of that control arm and compress the rear suspension. By doing so, this simulates the cars suspension travel and shows the engineers what the rear suspension and most importantly the rear sway bar goes through during a full cycle.

 

 

Right away the engineers could see the problem. Due to the design of the sway bar, the suspension is not actually twisting the bar. Instead, as the suspension compresses up into the wheel well the sway bar actually bends at the middle rather than twist like it should. Illustrated in the pictures below, you can see what the engineers saw. To start with this is what the sway bar looks like when both corners are at “full droop.” This means there is no load applied to either corner and the sway bar is “at rest.” In these images we have included a straight edge to better illustrate exactly what we’re talking about.

Factory sway bar at rest:

 
Here is an image of the factory sway bar with one corner compressed:

 
Not only was the sway bar not twisting properly but the factory rubber bushings were also deflecting in a manner they shouldn’t be.

 

To remedy the situation the engineers started by throwing out the factory design of the 2007 Nissan Altima sway bar altogether. After looking at the design of the bar, it was easy to see that the angle of the sway bar from the end link to the middle of the bar is simply insufficient and does not actually allow the bar to twist.
 
When looking at the factory sway bar compared to the STILLEN sway bar you can quickly see the entire design is different. By adding the additional bends in precise locations the sway bar now applies the torsional load from the suspension travel to the center of the sway bar in a twisting fashion as opposed to a leveraging angle. During the testing the STILLEN engineers performed the same test on the STILLEN sway bar as the factory sway bar. Here are the results:

STILLEN sway bar at rest:
 
 

STILLEN sway bar with one corner compressed:

 

STILLEN sway bar with one corner compressed, stock bushing very little deflection:
 

Due to the new end link mounting angle of the sway bar the engineers were uncomfortable re-using the factory end links as the angles did not match in a satisfactory position. Because of this STILLEN’s engineers designed new end links for the Nissan Altima, utilizing high durometer urethane couplers with high tensile strength steel hardware finished with a black powdercoating to protect from road debris and corrosion.

 
More Reasons Why You Should Upgrade To A STILLEN Altima Sway Bar

  • The STILLEN sway bar is more than a Nissan Altima replacement sway bar. By upgrading to STILLEN’s performance sway bar, you not only get a higher quality, better designed sway bar, but you also get to enjoy better handling it brings. Here are a few of the other benefits you can enjoy:
  • Better Handling – This sway bar is designed to handle comfortably on the street, while also making your Altima more fun to drive.
  • Warranty – Buy with confidence knowing that you are getting a genuine STILLEN sway bar that is made with the highest quality materials and comes with a manufacturer’s 1 year limited warranty.
  • Made in the USA – know that you are supporting American workers when you purchase STILLEN parts. For each STILLEN part, we make every effort possible to ensure that it is designed and manufactured in the US.
  • STILLEN 304236 – 2007-2013 Nissan Altima Sway Bar (Fits 2007-2013 Coupe or 2007-2012 Sedan)

If you have any questions about the STILLEN replacement sway bar for Nissan Altima Coupe or Sedan, please contact STILLEN at 866-250-5542 and they will be happy to answer any questions you have. If you live in the Southern California area and would like to get your new sway bar installed by the experts, please stop by the STILLEN performance shop. They feature an expert team that will be happy to install your sway bar for you or other Nissan Altima performance parts you may be considering like exhausts, air intakes, and more!

 

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*